Reproduction rear rocker panel flap for all 1968-72 Camaro and Firebird models. Prevents road splash and debris from entering and blocking the rocker panel drain area. This flap mounts on the rear side of the inner rocker panel. Sold as a pair.

Replacement seals that install under the cowl vent panel on each end.

Fits:
1967-68 Camaro

Replace your firewall steering column seal with this quality reproduction. Fits all 1967-68 Camaro models.

Replace your firewall steering column seal with this quality reproduction. Fits all 1969 Camaro models.

Reproductions of the original rear shock upper mounting plate for 1967-69 models. This EDP coated, die stamped, heavy steel plate mounts to the underside of the trunk floor.

Reproductions of the original rear shock mount reinforcement plates for all 1967-69 Camaro and Firebird models. This EDP coated, die stamped, heavy steel plate mounts to the trunk floor and has two threaded holes.

Reproduction of the original boot for 1967-69 Camaro and Firebird models that slides over the steering column at the base of the floor. Replacing your boot will help keep fluids from entering through the firewall area. This high quality reproduction is licensed as official GM Restoration parts.

Note: Installation requires removal of the steering column from the vehicle.

Reproduction LH quarter window reinforcement.

Fits:
1967-69 Camaro
1967-69 Firebird

Reproduction RH quarter window reinforcement.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace your old splash aprons with new reproductions and keep your engine compartment clean and free of water, salt and other road debris. Each set will install on both drivers and passengers side. Kits includes a full set of original type staples.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace your old splash aprons with new reproductions and keep your engine compartment clean and free of water, salt and other road debris. Each set will install on both drivers and passengers side. Kits includes a full set of original type staples.

Fits:
1969 Camaro
1969 Firebird

Reproduction of the original floor pan plastic plugs for use with floor pans and trunk pans on all 1967-68 Camaro and Firebird models. This is a 12 piece kit.

Accuate reproduction of original quarter panel stiffener used on al 1967-68 Camaro coupe models only. Commonly destroyed during 1/4 panel removal or missing from previous repair. Stiffener is welded to quarter panel on the underside of the trunk lid opening.

Accuate reproduction of original quarter panel stiffener used on al 1967-68 Camaro coupe models only. Commonly destroyed during 1/4 panel removal or missing from previous repair. Stiffener is welded to quarter panel on the underside of the trunk lid opening.

Accuate reproduction of original quarter panel stiffener used on al 1969 Camaro coupe models only. Commonly destroyed during 1/4 panel removal or missing from previous repair. Stiffener is welded to quarter panel on the underside of the trunk lid opening.

Accuate reproduction of original quarter panel stiffener used on al 1969 Camaro coupe models only. Commonly destroyed during 1/4 panel removal or missing from previous repair. Stiffener is welded to quarter panel on the underside of the trunk lid opening.

Reproduction tail panel braces LH or RH for all 1967-68 Camaro and Firebird models. These braces extend from the rear trunk floor pan to the inside of the rear end tail panel at the bumper mounting points. They are manufactured from original gauge steel and are EDP coated. They are ready to install, prime and paint.

Reproduction rear body panel braces LH and RH pair for all 1969 Camaro models. These braces extend from the rear trunk floor pan to the inside of the rear quarter panel at the bumper mounting points. They are manufactured from original gauge steel and are EDP coated. They are ready to install, prime and paint.

Reproduction of the original floor pan plastic plugs for use with floor pans and trunk pans on all 1969 Camaro and Firebird models.This is a 12 piece kit.

Accurate reproductions of original quarter panel reinforcement braces for all 1967-69 Camaro models. Commonly destroyed during 1/4 panel removal or missing from previous repair. Brace supports the edge of the quarter panel where the window felt attaches. It is very common for the quarter panel to devolop a stress crack near the end of the drip rail when this reinforcement is missing. Reinforcement must be welded to main body pillar and quarter panel.

Front lower quarter panel patch. 12W x 17L
Fits: All 1967-68 Camaro / Firebird models
Passenger side (RH)

Front lower quarter panel patch. 12W x 17L
Fits: All 1967-68 Camaro / Firebird models
Driver side (LH)

Reproduction tail panel braces LH and RH pair for all 1969 Camaro and Firebirds models. These braces extend from the rear trunk floor pan to the inside of the rear of tail panel at the bumper mounting points. They are manufactured from original gauge steel and are EDP coated. They are ready to install, prime and paint.

This panel will replace the lower rear section of the quarter panel. Each panel includes an offset flange for easy installation. Designed to allow wheel opening molding installation as required. Each patch panel is 13-3/4" high x 26" long. Fits all 1967-68 Camaro models.

This panel will replace the lower rear section of the quarter panel. Each panel includes an offset flange for easy installation. Designed to allow wheel opening molding installation as required. Each patch panel is 13-3/4" high x 26" long. Fits all 1967-68 Camaro models.

This panel will replace the lower rear section of the quarter panel. Each panel includes an offset flange for easy installation. Designed to allow wheel opening molding installation as required. Each patch panel is 16" high x 27" long. Fits all 1969 Camaro models.

This panel will replace the lower rear section of the quarter panel. Each panel includes an offset flange for easy installation. Designed to allow wheel opening molding installation as required. Each patch panel is 16" high x 27" long. Fits all 1969 Camaro models.

These reproduction firewall insulation pads mount onto the firewall area of the interior compartment. This pad fits all 1967-69 Camaro and Firebird models without AC. Its designed to exact factory specifications and manufactured using thick jute padding glued to a die-cut neoprene material, each insulation pad will fit, function and appear exactly as original. Die-cut to the exact dimensions of the firewall opening to allow room for the steering column, heater exchanger box, emergency brake cable, etc. Includes mounting clips for installation when required.

IMPORTANT: 1967-69 insulation pads not scored for ventilation systems - must be cut for appropriate system

Note: The jute material attaches directly to the firewall. On vehicles equipped without air conditioning, it will be necessary to cut out the area for the heater box assembly. This is due to the availability of a factory heater delete option which required a solid firewall pad.

These reproduction firewall insulation pads mount onto the firewall area of the interior compartment. This pad fits all 1967-69 Camaro and Firebird models with AC. Die-cut to the exact dimensions of the firewall opening to allow room for the steering column, heater box, emergency brake cable, etc. Includes mounting clips for installation when required.

IMPORTANT: 1967-69 insulation pads not scored for ventilation systems - must be cut for appropriate system

Note: The jute material attaches directly to the firewall.

This is the outer section of the wheelhouse assembly which installs between the quarter panel and inner wheelhouse panel. Has the correct lip at the wheel opening allowing easy installation of wheel well moldings. When installed, the panel will mate with the inner wheelhouse forming the complete enclosure. Shipped double oversize.

Fits:
1967-68 Camaro
1967-68 Firebird