Hardware used to install the lower steering column cover. Includes the correct screw and j-nuts.

Fits: 1969 Camaro / Firebird

Reproduction of the horn pin, spring and retainer for all Cushion/Comfort grip wheels. (Note: non-wood wheels use spring and retainer only).
Fits:
1967-81 Camaro
1967-81 Firebird
1970 Chevelle

Standard horn cap mounting ring which is necessary when installing 1967 or 1968 Camaro horn caps. This rubber ring provides the necessary interlock between horn cap and horn contact. It is not included when purchasing a horn cap and is essential for installation.

Replacement seals that install under the cowl vent panel on each end.

Fits:
1967-68 Camaro

Replace your firewall steering column seal with this quality reproduction. Fits all 1967-68 Camaro models.

Replace your firewall steering column seal with this quality reproduction. Fits all 1969 Camaro models.

This quality reproduction of the Emergency flasher knob with short knobs. This knob is die cast and chrome plated, just like the original and features "FLASHER" lettering on the front and rear of the stem. GM licensed.

Reproduction of the RS steering wheel emblem. Comes with retainers.

Fits: 1969 Camaro

Reproduction of the SS steering wheel emblem. Comes with retainers.

Fits:
1969 Camaro

This is a high quality reproduction of the Emergency flasher knob. This knob is die cast and chrome plated, just like the original and features "FLASHER" lettering on the front and rear of the stem. GM licensed.
1967-69 Camaro
1967-69 Firebird
1967-70 Chevelle

Reproduction of the original boot for 1967-69 Camaro and Firebird models that slides over the steering column at the base of the floor. Replacing your boot will help keep fluids from entering through the firewall area. This high quality reproduction is licensed as official GM Restoration parts.

Note: Installation requires removal of the steering column from the vehicle.

Turn signal lever with or without tilt wheel.

Fits all:
1968-70 Camaro

Reproduction of the horn cap used on wood and comfort grip steering wheels.

Fits:
1967-70 Camaro
1967-70 Firebird
1970 Chevelle

Turn signal lever with tilt wheel. Note: Will work on non tilt wheels but not technically correct.

Fits:
1967 Camaro
1967 Firebird

Correct reproduction horn buttons used on all 1969 Camaro steering wheels. Includes both the RH and LH horn buttons.

Tilt wheel release lever.
Fits:
1967 Camaro

Tilt wheel release lever.
Fits:
1968-70 Camaro
1968-70 Firebird

Correct reproduction of the original horn buttons contacts used on all 1969 Camaro standard steering wheels. Includes both the RH and LH horn button contacts.

Hardware to mount steering wheel to column and includes horn contact with screws which allows you to install horn cap. Mounts all comfort grip and wood wheels.
Fits:
1967-69 Camaro
1967-69 Firebird

Steering wheel contact and mounting kit for standard factory steering wheel.
Fits:
1967 Camaro
1968 Camaro
1971-79 Camaro w/4 Spoke Sport Wheel

Reproduction lower steering column cover.
Fits: 1969 Camaro

Wood steering wheel horn contact and mounting kit without tilt column.

Fits:
1969 Camaro
1969 Firebird

Reproduction steering coupling joint for 1967-69 Camaro models with power steering and used on other various 1959-79 GM models .

Couplier Specs:

• Shaft Size: 13/16" - 36 spline
• Total OD: 3 1/4"

Fits:

• 1967-76 Camaro
• 1967-76 Pontiac Firebird, Trans Am
• 1964-73 Chevelle
• 1959-79 Other GM Models

Reproduction lower steering column cover.

Fit:
1967-68 Camaro
1967-68 Firebird

This is an excellent reproduction of the original horn button cap used on all 1967-69 Camaro models equipped with the optional Wood or Comfort Grip steering wheel. This cap includes the bow tie emblem in the center with a blue background with a red white and blue border.  Its officially licensed by GM

Reproduction steering coupling joint for 1967-69 Camaro models with manual steering and used on other various 1959-82 GM models .

Couplier Specs: Shaft Size: ¾" fine spline w/o flat at bolt head side
Spline Count: 32
Total OD: 3 5/32"
Bolt Size: 5/16"
Bolt Spacing: 2-3/8" center to center
Pin Diameter: 5/16" & 3/8"
Pin Spacing: 2-1/2" center to center
Grounding Plate: no

Fits:
1967-69 Camaro
1967-69 Pontiac Firebird, Trans Am
1964-69 Chevelle
1959-82 Other GM Models

Steering wheel mounting hub use to mount Walnut steering wheels. Does not include screws.

Steering wheel mounting hub use to mount Rosewood and Comfort Grip steering wheels. Does not include screws.

Reproduction of the original cherry steering wheel shroud used on all 1969 Camaro models. Made to the correct plastic grain finish. This shroud will install on original GM and reproduction steering wheels. The shroud emblem and mounting screws are no included.

Reproduction of the original black steering wheel shroud used on all 1969 Camaro models. Made to the correct plastic grain finish. This shroud will install on original GM and reproduction steering wheels. The shroud emblem and mounting screws are no included.