These clips are installed on the bottom ends of the shroud. Provisions are molded into the shroud allowing attachment of the shroud to the radiator. Each vehicle requires two clips. This is a 2-piece kit.
Fits:
1967-69 Camaro
1967-69 Firebird
1968-72 Chevelle

Rubber bumper that fits on top of the hood adjustment screw. Includes 2 bumpers.
Fits:
1967-81 Camaro
1967-81 Firebird
1964-72 Chevelle
1964-72 El Camino

Wiring harness plastic straps. Includes 2 straps.

Fits:
1967-69 Camaro
1967-69 Firebird
1964-72 Chevelle

Plastic loop straps for holding washer hose to fender. 2 pieces
Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1968-72 El Camino

Reproduction battery tray clamp. Manufactured in steel as original. Mounting screw included.
Fits:
1967-81 Camaro
1967-69 Firebird
1964-72 Chevelle

Correct chrome wing nut for chrome lid air cleaners. Will work on any 1/4"-20 carburetor stud found on Rochester and Holley carburetors.

This hose bracket was attached to the top of the alternator and held the heater hose in place. This is a excellent reproduction of the original.
Fits:
1968-69 Camaro
1968-69 Firebird
1968-72 Chevelle
1968-72 el Camino

Reproduction of the original battery junction block. This items is used to provide a junction point for your battery to your wiring harness by isolating it from the body.
Fits:
1967-69 Camaro
1967-69 Firebird
1968-69 Chevelle

This hose clip is designed to secure a pair of heater hoses to the inner fender skirt to prevent damage of the hoses and keep the engine compartment neat and tidy in appearance. This is a excellent reproduction of the original.
Fits:
1967-69 Camaro
196-69 Firebird
1968-72 Chevelle
1968-72 El Camino

Accurate reproduction of the 1967-69 Camaro/Firebird and 1968-72 Chevelle firewall wire gutter with correct exterior finish and slotted mounting holes. Includes correct size, plated mounting screws.
Fits:
1967-69 Camaro
1968-72 Chevelle
1967-69 Firebird

Correct Bumper and screw assembly to adjust front of hood height. Includes 2 bumpers and 2 screws.
Fits:
1967-81 Camaro
1967-81 Firebird
1964-72 Chevelle
1964-72 El Camino

Correct reproduction hardware to install factory style radiator.

Fits:
1967-68 Camaro
1967-68 Firebird

Correct reproduction hardware to install factory style radiator.

Fits:
1969 Camaro
1969 Firebird

Elbow that inserts into the RH passenger side valve cover and completes the connection to the air cleaner hose. For 1967-70 Big Block with 1"i.d. x 3 1/2" L w/90° bend.
Fits:
1967-70 Camaro
1966-70 Chevelle
1966-70 El Camino

Reproduction of the original battery tray. Stamped steel reproduction in EDP primer.

Fits:
1967-69 Camaro
1967-69 Firebird
1966 Chevelle

Four correct gauge and hole size metal plates to repair rusted, enlarged hole or thin tops of the four sub-frame to body mounting brackets. Welding required.
Will work for all 1967-74 Camaro / Firebird models and all 1968-74 Nova models.

Correct reproduction of the original fan shroud bracket for 1967-68 Camaro big blocks and 1967-69 small block Camaro and 1967-69 Firebird models. Bracket holds fan shroud in place, connecting to the radiator support. This reproduction includes three correct 5/16"-18 J-nutsallowing for correct installation.

Reproduction battery tray and clamp with screw.

Fits:
1966 Chevelle
1967-69 Camaro
1967-69 Firebird

Correct hardware to mount heater box to firewall on non AC cars with small block and big block.
Fits:
1967-81 Camaro
1967-81 Firebird

Accurate reproductions of the original, these two high-quality, smooth hoses from OER are 5/8" and 3/4" diameter and 4.5 ft in length. Only the 3/4" has the GM Logo. The 5/8" hose was never issued with the GM Logo. These hoses are "show-quality" for the serious restoration enthusiast.

Fits:

· 1967-69 Camaro small or big block

· 1967-69 Firebird including 455

· 1967-72 Chevrolet / GMC truck small or big block

· 1967-69 Impala / full size small or big block

· 1962-79 Chevy II / Nova small or big block

Replace your heater box seals with precision die-cut neoprene seals that restore original heating and sealing efficiency. Each complete kit includes core to box seal, main duct flap door, intermediate plenum flap door, and core outlet tube seals. All seals are die cut for exact replacement. Note: Not for use on vehicles equipped with AC. Fits all small block and big block heater boxes.
Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1968-72 El Camino

GM Universal 2 piece adjustable throttle rod for Small Block with Rochester 4 BBL carburetor.

Fits:
1967-69 Camaro
1967-69 Firebird
1968-72 Chevelle

Replace your original rusted damaged sub-frame and radiator hardware with this quality reproduction kit. This kit contains all the bolts, washers and nuts to complete the job.

Fits:
1967-72 Camaro
1967-72 Firebird

Replace your original radiator support bushings with this quality reproduction kit. This kit contains bushings only. This kit is not technically correct for 1973-81 Camaro's but will work.

Fits:
1967-81 Camaro
1967-81 Firebird

These original style black fender to radiator support bars install from the fender to the radiator support on each side under the hood. These bars when installed, will help to keep the front sheet metal from flexing. Includes 4 black oxide mounting bolts.

Fits:
1967-69 Camaro
1967-69 Firebird

This is an authentic reproduction of the original 1959-1972 WITTEK MFG tower-style radiator and heater hose clamps. Includes a total of eight clamps. Originally used from 1959-72, these can also be used on older models that have been converted to custom radiators with larger sized water outlets. NOTE: Some vehicles may require two additional clamps at the heater control valve.

Kit Includes:

• Two 2-1/16" upper radiator hose clamps
• Two 2-1/4" lower radiator hose clamps
• Two 5/8" heater hose clamps
• Two 3/4" heater hose clamps

Replace your original style black fender to radiator support bars with these polished chrome bars. They install from the fender to the radiator support on each side under the hood. These bars when installed, will help to keep the front sheet metal from flexing. Comes with chrome mounting hardware.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace your original radiator support bushings and hardware with this quality reproduction kit. This kit contains all the bushings, bolts, washers and nuts to complete the job.
Fits:
1967-81 Camaro
1967-81 Firebird

Radiator Support Bushing & Hardware Kit for 1967-81 Camaro Firebird models.

Reproduction steering coupling joint for 1967-69 Camaro models with power steering and used on other various 1959-79 GM models .

Couplier Specs:

• Shaft Size: 13/16" - 36 spline
• Total OD: 3 1/4"

Fits:

• 1967-76 Camaro
• 1967-76 Pontiac Firebird, Trans Am
• 1964-73 Chevelle
• 1959-79 Other GM Models