Hardware used to install the lower steering column cover. Includes the correct screw and j-nuts.

Fits: 1969 Camaro / Firebird

Reproduction of the horn pin, spring and retainer for all Cushion/Comfort grip wheels. (Note: non-wood wheels use spring and retainer only).
Fits:
1967-81 Camaro
1967-81 Firebird
1970 Chevelle

This factory-correct, 4-piece hardware kit provides secure coupling of the shaft at the rag joint.
Fits:
1967-78 Camaro/Firebird
1967-72 Chevelle

Replacement seals that install under the cowl vent panel on each end.

Fits:
1967-68 Camaro

Replace your firewall steering column seal with this quality reproduction. Fits all 1967-68 Camaro models.

Replace your firewall steering column seal with this quality reproduction. Fits all 1969 Camaro models.

This quality reproduction of the Emergency flasher knob with short knobs. This knob is die cast and chrome plated, just like the original and features "FLASHER" lettering on the front and rear of the stem. GM licensed.

Factory-correct, firewall plate hardware mount set. Correct bolts, screws, and rubber sealing washers for all 67 - 68 Camaro models.
Fits:
1967-68 Camaro
1967-68 Firebird

This is a high quality reproduction of the Emergency flasher knob. This knob is die cast and chrome plated, just like the original and features "FLASHER" lettering on the front and rear of the stem. GM licensed.
1967-69 Camaro
1967-69 Firebird
1967-70 Chevelle

Reproduction of the original boot for 1967-69 Camaro and Firebird models that slides over the steering column at the base of the floor. Replacing your boot will help keep fluids from entering through the firewall area. This high quality reproduction is licensed as official GM Restoration parts.

Note: Installation requires removal of the steering column from the vehicle.

Reproduction of the horn cap used on wood and comfort grip steering wheels.

Fits:
1967-70 Camaro
1967-70 Firebird
1968-70 Chevelle

GM hazard knob kit used to replace broken or missing emergency/hazard flasher knob on steering column.
Fits:
GM Cars & Trucks from 1977-2005

Turn signal lever with tilt wheel. Note: Will work on non tilt wheels but not technically correct.

Fits:
1967 Camaro
1967 Firebird

Tilt wheel release lever.
Fits:
1968-70 Chevelle
1968-70 Camaro
1968-70 Firebird

Hardware to mount steering wheel to column and includes horn contact with screws which allows you to install horn cap.

NOTE: Mounts all GM comfort grip and wooden steering wheels.

Tilt wheel release lever.
Fits:
1967 Camaro
1967 Firebird

Reproduction lower steering column cover.

Fit:
1967-68 Camaro
1967-68 Firebird

Reproduction steering coupling joint for 1967-69 Camaro models with power steering and used on other various 1959-79 GM models .

Coupler Specs:

• Shaft Size: 13/16" - 36 spline
• Total OD: 3 1/4"

Fits:

• 1967-76 Camaro
• 1967-76 Pontiac Firebird, Trans Am
• 1964-73 Chevelle
• 1969-79 Nova

Wood steering wheel horn contact and mounting kit without tilt column.

Fits:
1969-70 Chevelle
1969 Camaro
1969 Firebird

Reproduction steering coupling joint for 1967-69 Camaro models with manual steering and used on other various 1959-82 GM models .

Couplier Specs: Shaft Size: ¾" fine spline w/o flat at bolt head side
Spline Count: 32
Total OD: 3 5/32"
Bolt Size: 5/16"
Bolt Spacing: 2-3/8" center to center
Pin Diameter: 5/16" & 3/8"
Pin Spacing: 2-1/2" center to center
Grounding Plate: no

Fits:
1967-69 Camaro
1967-69 Pontiac Firebird, Trans Am
1964-69 Chevelle
1959-82 Other GM Models