Trunk latch 9-piece hardware kit to install trunk latch in the trunk.
Fits:
1967-81 Camaro
1968-72 Chevelle
1967-81 Firebird

Reproduction of the original floor pan plug for use with floor pans and truck pans. Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1962-72 Nova

Rubber trunk bumpers 2 piece set.
Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1966-79 Chevy II Nova

Reproductions of the 1967-81 GM trunk lid hinge bolts used on Camaro/Firebird/Chevelle models. Kit includes 4 pieces.

Correct reproduction of the spare tire anchor wing nut.
Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1966-79 Chevy II Nova

Replacement trunk latch support bracket. Welds inside trunk and the trunk latch installs into it.
Fits:
1974-81 Camaro
1974-81 Firebird

Correct reproduction of the spare tire anchor "J" hook.
Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1966-79 Chevy II Nova

Trunk floor drain plug.
Fits:
1971-81 Camaro
1971-81 Firebird

Correct reproduction of the spare tire anchor plate that is welded to the trunk floor pan that sats as a clamp by holding the spare tire hold down rod in place after the nut is tightened.

Fits:
1967-81 Camaro
1967-81 Firebird

Reproduction of the spare tire anchor "J" hook and wing nut.
Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1966-79 Chevy II Nova

Reproduction of the original small, galvanized-steel, round (1 3/8" diam) floor pan plug.
Fits:
1975-81 Camaro
1975-81 Firebird

Clips used to hold wiring harness in place. Includes 2 clips

Fits:
1970-73 Camaro
1970-73 Firebird

Reproduction of the original floor pan plug for use with floor pans and truck pans.

Fits:
1967-81 Camaro
1967-81 Firebird
1962-72 Nova

Reproduction of the original galvanized steel floor pan plug with tabs. (3 9/16" x 3 3/4")

Fits:
1975-81 Camaro
1975-81 Firebird

Quality steel replacement for the trunk latch support for all 1970-81 Camaro Firebird models. Mounts between the trunk floor and tail panel. This quality stamped steel piece acts as a mount for the trunk latch assembly. Includes mounting hardware.

Correct reproduction of the trunk lid torque tension rods for all 1970-81 Camaro / Firebird models with trunk lid spoilers. Sold in pairs only.

Reproduction of the upper jack bracket for use on all 1970-73 Camaro models.

Reproduction of the original trunk lid latch assembly originally installed on 1971-81 Camaro and Firebird models. This unit installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. This assembly does not include the shaft or lock cylinder assembly, which are available separately.

Reproduction trunk drop off side panels for all 1970-73 Camaro models and are exact reproductions of the original panels. These panels are located where the trunk pan meets the lower rear quarter panel. It will look and fit just like the original.

Reproduction trunk drop off side panels for all 1970-73 Camaro models and are exact reproductions of the original panels. These panels are located where the trunk pan meets the lower rear quarter panel. It will look and fit just like the original.

Reproduction trunk drop off side panels for all 1974-81 Camaro models and are exact reproductions of the original panels. These panels are located where the trunk pan meets the lower rear quarter panel. It will look and fit just like the original.

Reproduction trunk drop off side panels for all 1974-81 Camaro models and are exact reproductions of the original panels. These panels are located where the trunk pan meets the lower rear quarter panel. It will look and fit just like the original.

Quality steel replace for the tail panel brace and trunk latch support for all 1970-73 Camaro and Firebird models. Mounts between the trunk floor and tail panel. This quality stamped steel piece acts as a brace for the tail panel and mount for the trunk latch assembly.

Correct trunk lid torque tension rods for all 1967-69 Camaro / Firebird models with trunk lid spoilers. Includes correct molded rubber sleeves on both as the originals.

Accurate reproductions of original gutter edge molding for all 1970-81 Camaro and Firebird models to finish out both quarters, allowing the installation of trunk weatherstrip. Needed on all reproduction full quarters or for repair on your rusted originals.  All new tooling! The uniform edge on these panels gives the trunk a correct factory look.

Precise reproduction of the original trunk lid hinge assembly on all 1970-81 Camaro and Firebird models. Quality-manufactured in stamped steel to factory specifications, it is an exact replicate of the original in fit and appearance. This assembly is EDP-coated to protect against rust and corrosion.

Fits:
1970-81 Camaro
1970-81 Firebird

Precise reproduction of the original trunk lid hinge assembly on all 1970-81 Camaro and Firebird models. Quality-manufactured in stamped steel to factory specifications, it is an exact replicate of the original in fit and appearance. This assembly is EDP-coated to protect against rust and corrosion.

Fits:
1970-81 Camaro
1970-81 Firebird

IN-STORE PICKUP ONLY. This product was received slightly damaged during shipping. It has slight bends on both bottom corners. The trunk catch is also missing. (See images) Otherwise, it is in new condition and still very useable.

Reproduction deck lid including spoiler holes pre-drilled for rear deck 3-PIECE SPOILER. NOTE: This is NOT a deck lid with pre-drilled holes for the 1-piece spoiler.

Fits:
1970-81 Camaro
1970-81 Firebird

Reproduction of the original trunk floor for use on all 1970-73 Camaro and Firebird models. Replace your old rusted out trunk floor with these high quality reproductions. Each trunk pan is reproduced to factory specifications and will replace the entire bottom portion of the trunk floor. The pan also includes correct reinforcement seams built in the panel for added support.  Note: Shipped Truck Freight. (Size 42 w x 37 L)

Correct 4-piece reproduction gas tank brace kit used on all 1970-73 Camaro and Firebird models. These braces will provide the reinforcement between the trunk floor and the gas tank. Braces also provide mounting points for the gas tank straps.