Rubber floor plug. 2" diameter and fits a 1-1/2" diameter hole.

Reproduction of the original floor pan plug for use with floor pans and truck pans. Fits:
1967-81 Camaro
1967-81 Firebird
1968-72 Chevelle
1962-72 Nova

The headlight dimmer switch is located on the drivers front floor and used to switch the headlights from low beam to high beam. Dimmer switch on 79-81 Firebirds are on the steering column.
Fits:
1967-81 Camaro
1967-78 Firebird
1964-72 Chevelle

Reproduction of the original floor pan plug for use with floor pans and truck pans.

Fits:
1967-81 Camaro
1967-81 Firebird
1962-72 Nova

Accurate reproduction of the rear axle pinion bumper manufactured from molded rubber to provide original fit and appearance. This bumper attaches to a slotted bracket under the floor pan above the differential housing. Designed to prevent the floor from bottoming out on the pinion area of the differential.
Fits:
1967 Camaro (2nd design)
1967 Firebird (2nd design)
1968-69 Camaro
1968-69 Firebird
1968-69 Nova

Reproduction of the stamped steel brace that goes under the rear seat on the leading edge of the rear seat riser on all 1967-1969 Camaro and Firebird models.

Reproduction of the stamped steel brace that goes under the rear seat on the leading edge of the rear seat riser on all 1967-1969 Camaro and Firebird models.

Replace the damaged or rusted out rear section of your floor pan with these high quality reproductions. Each partial floor pan is manufactured to replace the original exactly and is produced in the same configuration as the original. All panels also feature offset welding ledges for easier installation. The rear partial floor pans will cover the area from just behind the front seat to approximately 3" behind the front section of the rear seat. Shipped oversize.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace the damaged or rusted out rear section of your floor pan with these high quality reproductions. Each partial floor pan is manufactured to replace the original exactly and is produced in the same configuration as the original. All panels also feature offset welding ledges for easier installation. The rear partial floor pans will cover the area from just behind the front seat to approximately 3" behind the front section of the rear seat. Shipped oversize.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace the damaged or rusted out front section of your floor pan with these high quality reproductions. Each partial floor pan is manufactured to replace the original exactly and is produced in the same configuration as the original. All panels also feature offset welding ledges for easier installation. The front partial floor pans will cover the area from the firewall extension to the area just behind the front seats. Note: The seat track mounting area must be removed from the existing panel and reinstalled on the reproduction panel. Shipped oversize.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace the damaged or rusted out front section of your floor pan with these high quality reproductions. Each partial floor pan is manufactured to replace the original exactly and is produced in the same configuration as the original. All panels also feature offset welding ledges for easier installation. The front partial floor pans will cover the area from the firewall extension to the area just behind the front seats. Note: The seat track mounting area must be removed from the existing panel and reinstalled on the reproduction panel. Shipped oversize.

Fits:
1967-69 Camaro
1967-69 Firebird

Reproduction of the 1967-69 Camaro and Firebird under rear seat brace. This brace that goes on the passenger side from the floor pan to the package try under the rear seat.

Reproduction of the 1967-69 Camaro and Firebird under rear seat brace. This brace that goes on the driver side from the floor pan to the package try under the rear seat.

Correct reproduction front seat brace for all 1967-1969 Camaro and Firebird  models. These braces weld to the floor pans and support the seat platform.

Correct reproduction front seat brace for all 1967-1969 Camaro and Firebird models. These braces weld to the floor pans and support the seat platform.

High quality convertible floor pan brace for 1967-69 convertible. These quality stamped steel reproductions will fit and install just like the originals. These are a must when replacing the floor pan on a convertible.

Fits:
1967-69 Camaro
1967-69 Firebird

High quality convertible floor pan brace for 1967-69 convertible.These quality stamped steel reproductions will fit and install just like the originals. These are a must when replacing the floor pan on a convertible.

Fits:
1967-69 Camaro
1967-69 Firebird

This is a patch panel to replace the lower section of the firewall on all 1967-69 Camaro and Firebirdmodels. This toe board is the extension piece that connects the front floor pan to the firewall.

This is a patch panel to replace the lower section of the firewall on all 1967-69 Camaroand Firebird models. This toe board is the extension piece that connects the front floor pan to the firewall.

Reproduction front seat platform used on all 1967-69 Camaro and Firebird coupe models. This panel replaces the area under the front bucket seat and are attached to the floor pans to provide a mounting point for the seat frames.

Reproduction front seat platform used on all 1967-69 Camaro snd Firebird coupe models. This panel replaces the area under the front bucket seat and are attached to the floor pans to provide a mounting point for the seat frames.

This is a stamped steel reproduction of the firewall to floor pan brace. This panel runs from the firewall, down under the vehicle to the floor cross brace on all 1969 Camaro and Friebird models.

This is a stamped steel reproduction of the firewall to floor pan brace. This panel runs from the firewall, down under the vehicle to the floor cross brace on all 1969 Camaro and Firebird models.

Repair the damage done by a hack-job shifter install without replacing the entire floor pan with this high quality stamped steel repair panel. It measures 19-1/2" long x 6" high and installs on all 67-69 Camaro and Firebird models.

Reproduction front seat platform used on all 1967-69 Camaro and Firebird convertible models. This panel replaces the area under the front bucket seat and are attached to the floor pans to provide a mounting point for the seat frames.

Reproduction front seat platform used on all 1967-69 Camaro and Firebird convertible models. This panel replaces the area under the front bucket seat and are attached to the floor pans to provide a mounting point for the seat frames.

Replace your existing floor pans with these high quality reproductions! Each floor pan is manufactured to exact specifications and extends from the rear seat section to the firewall extension. Our floor pans feature additional metal which extends upward near the transmission tunnel allowing more coverage then other floor pans currently on the market. Each panel includes the correct drain hole area cut out. The seat platform is not included and must be removed from existing panel and reinstalled on the reproduction panel. Reproduction seat platforms are available separately. Note: Shipped double oversize.

Fits:
1967-69 Camaro
1967-69 Firebird

Replace your existing floor pans with these high quality reproductions! Each floor pan is manufactured to exact specifications and extends from the rear seat section to the firewall extension. Our floor pans feature additional metal which extends upward near the transmission tunnel allowing more coverage then other floor pans currently on the market. Each panel includes the correct drain hole area cut out. The seat platform is not included and must be removed from existing panel and reinstalled on the reproduction panel. Reproduction seat platforms are available separately. Note: Shipped double oversize.

Fits:
1967-69 Camaro
1967-69 Firebird

Under rear seat pan - RH

Fits:
1970-74 Camaro
1970-74 Firebird
1970-74 Trans Am

This is a quality steel reproduction of the under-floor pan brace found on all 1967-69 Camaro and Firebird convertibles. Don't trust your rusty original replace it with the is quality piece.