1967-81 GM Fan Shroud Clip Kit
These clips are installed on the bottom ends of the shroud. Provisions are molded into the shroud allowing attachment of the shroud to the radiator. Each vehicle requires two clips. This is a 2-piece kit.
1964-81 Hood Adjuster Bumper, Pair
Rubber bumper that fits on top of the hood adjustment screw. Includes 2 bumpers.
1964-72 El Camino
1964-72 GM Wire Straps
Wiring harness plastic straps. Includes 2 straps.
1968-72 GM Heater Hose Bracket
This hose bracket was attached to the top of the alternator and held the heater hose in place. This is a excellent reproduction of the original.
1968-72 el Camino
1967-69 Camaro/Firebird/Chevelle Battery Junction Block
Reproduction of the original battery junction block. This items is used to provide a junction point for your battery to your wiring harness by isolating it from the body.
1967-72 GM Heater Hose Bracket
This hose clip is designed to secure a pair of heater hoses to the inner fender skirt to prevent damage of the hoses and keep the engine compartment neat and tidy in appearance. This is a excellent reproduction of the original.
1968-72 El Camino
1967-69 Camaro Chevelle Firebird Fierwall Wire Gutter
Accurate reproduction of the 1967-69 Camaro/Firebird and 1968-72 Chevelle firewall wire gutter with correct exterior finish and slotted mounting holes. Includes correct size, plated mounting screws.
1967-70 Camaro Chevelle BB Valve Cover Elbow
Elbow that inserts into the RH passenger side valve cover and completes the connection to the air cleaner hose. For 1967-70 Big Block with 1"i.d. x 3 1/2" L w/90° bend.
1966-70 El Camino
1969-72 GM Small Block Valve Cover Elbow
Elbow that inserts into the RH passenger side valve cover and completes the connection to the air cleaner hose. For 1969-72 small block with 3/4"o.d. x 3 1/2" L w/90° bend
1969-72 El Camino
1968-72 Chevelle Battery Tray
Reproduction of the original battery tray for use on all 1968-72 Chevelle models. Stamped steel reproduction in EDP primer.
1967-81 Heater Box Seal Kit
Replace your heater box seals with precision die-cut neoprene seals that restore original heating and sealing efficiency. Each complete kit includes core to box seal, main duct flap door, intermediate plenum flap door, and core outlet tube seals. All seals are die cut for exact replacement. Note: Not for use on vehicles equipped with AC. Fits all small block and big block heater boxes.
1968-72 El Camino
1959-1972 WITTEK MFG Tower-Style Hose Clamps, 8-Pcs
This is an authentic reproduction of the original 1959-1972 WITTEK MFG tower-style radiator and heater hose clamps. Includes a total of eight clamps. Originally used from 1959-72, these can also be used on older models that have been converted to custom radiators with larger sized water outlets. NOTE: Some vehicles may require two additional clamps at the heater control valve.
- Two 2-1/16" upper radiator hose clamps
- Two 2-1/4" lower radiator hose clamps
- Two 5/8" heater hose clamps
- Two 3/4" heater hose clamps
1970-72 Chevelle Radiator Top Plate, 4-Hole
Quality reproduction of 4-hole radiator top plate, including correct welded tab. Color = Satin Black
Fits: 1968-72 Chevelle
NOTE: For use with Special High Performance or Heavy Duty Cooling, LS6 / L78 equipped vehicles.
1970-72 Chevelle Radiator Top Plate, 3-Hole
Quality reproduction of 3-hole radiator top plate, including correct welded tab. Color = Satin Black
Fits: 1968-72 Chevelle
NOTE: For use on Chevelle's with Naturally Aspirated Fuel Systems.
1964-73 Steering Couplier w/ Power Steering
Reproduction steering coupling joint for 1967-69 Camaro models with power steering and used on other various 1959-79 GM models .
- Shaft Size: 13/16" - 36 spline
- Total OD: 3 1/4"
- 1967-76 Camaro
- 1967-76 Pontiac Firebird, Trans Am
- 1964-73 Chevelle
- 1959-79 Other GM Models
1970-72 Chevelle Upper Radiator Support
Correct reproduction and is ready to install. Features pre-drilled holes for easy installation on all 6 cylinder or 8 cylinder including big blocks. This radiator support is used on all 1970-72 Chevelle models.
1967-69 Steering Couplier w/ Manual Steering
Reproduction steering coupling joint for 1967-69 Camaro models with manual steering and used on other various 1959-82 GM models .
Couplier Specs: Shaft Size: ¾" fine spline w/o flat at bolt head side
Spline Count: 32
Total OD: 3 5/32"
Bolt Size: 5/16"
Bolt Spacing: 2-3/8" center to center
Pin Diameter: 5/16" & 3/8"
Pin Spacing: 2-1/2" center to center
Grounding Plate: no
1967-69 Pontiac Firebird, Trans Am
1959-82 Other GM Models